manualshive.com logo in svg

IEI Technology eKINO-BT, User Manual

Share
Download
IEI Technology eKINO-BT User Manual Download Page 3

 

 

eKINO-BT Mini-ITX SBC 

Page iii

Copyright 

COPYRIGHT NOTICE 

The information in this document is subject to change without prior notice in order to 

improve reliability, design and function and does not represent a commitment on the part 

of the manufacturer. 

In no event will the manufacturer be liable for direct, indirect, special, incidental, or 

consequential damages arising out of the use or inability to use the product or 

documentation, even if advised of the possibility of such damages. 

This document contains proprietary information protected by copyright. All rights are 

reserved. No part of this manual may be reproduced by any mechanical, electronic, or 

other means in any form without prior written permission of the manufacturer.

 

TRADEMARKS 

All registered trademarks and product names mentioned herein are used for identification 

purposes only and may be trademarks and/or registered trademarks of their respective 

owners.  

Summary of Contents for eKINO-BT






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands