manualshive.com logo in svg

IEI Technology eKINO-BT, User Manual

Share
Download
IEI Technology eKINO-BT User Manual Download Page 33

 

 

eKINO-BT Mini-ITX SBC 

Page 19

3.1.3 External Interface Panel Connectors 

The table below lists the rear panel connectors on the eKINO-BT. Detailed descriptions of 

these connectors can be found in a later section. 

Connector 

Type 

Label 

9 V ~ 26 V DC in connector 

4-pin mini-DIN 

SPWR_IN1 

Audio jacks (mic-in, line-out) 

Audio jack 

AUDIO1 

Ethernet and USB 2.0 connectors 

RJ-45 and USB 2.0 

LAN_USB2 

Ethernet and USB 3.0 connectors 

RJ-45 and USB 3.0 

LAN_USB1 

RS-232 serial ports 

DB-9 

COM1, COM2, 

COM3 

VGA connector 

15-pin female

 

VGA1 

Table 3-2: Rear Panel Connectors 

3.2 Internal Peripheral Connectors 

Internal peripheral connectors are found on the motherboard and are only accessible 

when the motherboard is outside of the chassis. This section has complete descriptions of 

all the internal, peripheral connectors on the eKINO-BT. 

3.2.1 9 V ~ 26 V Power Connector 

CN Label: 

VIN1 

CN Type: 

4-pin Molex power connector 

CN Location: 

See 

Figure 3-3

 

CN Pinouts: 

See 

Table 3-3

 

This connector provides power to the system. 

Summary of Contents for eKINO-BT






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands