IEI Technology eKINO-BT User Manual Download

Page: 152 / 157

eKINO-BT Mini-ITX SBC

Page 138

D.1 Introduction

The DIO connector on the eKINO-BT is interfaced to GPIO ports on the Super I/O chipset.

The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital

outputs are generally control signals that control the on/off circuit of external devices or

TTL devices. Data can be read or written to the selected address to enable the DIO

functions.

NOTE:

For further information, please refer to the datasheet for the Super I/O

chipset.

The BIOS interrupt call

INT 15H

controls the digital I/O.

INT 15H:

AH – 6FH

Sub-function:
AL – 8

:Set the digital port as INPUT

:Digital I/O input value

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands