IEI Technology eKINO-BT User Manual Download

Page: 111 / 157

eKINO-BT Mini-ITX SBC

Page 97

Advanced

Wake system with Fixed Time

[Disabled]

Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified
----------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 9: RTC Wake Settings

Wake system with Fixed Time [Disabled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.

Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake

event

Enabled

If selected, the

Wake up every day

option appears

allowing you to enable to disable the system to wake

every day at the specified time. Besides, the

following options appear with values that can be

selected:

Wake up every day

Wake

date

Wake

hour

Wake up minute

Wake

second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands