IEI Technology eKINO-BT User Manual Download

Page: 123 / 157

eKINO-BT Mini-ITX SBC

Page 109

Audio Controller [Enabled]

Use the

Audio Controller

BIOS option to enable or disable the High Definition Audio

controller.

Disabled

The High Definition Audio controller is disabled.

Enabled D

EFAULT

The High Definition Audio controller is enabled.

5.4.2.1 PCI Express Configuration

Use the

PCI Express Configuration

menu (

BIOS Menu 19

) to configure the PCI Express

slots.

Chipset

PCI Express Configuration

M_PCIE1

Speed

[Auto]

PCIE1

Speed

[Auto]

----------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized Defaults
F4: Save & Exit
ESC: Exit

BIOS Menu 19: PCI Express Configuration

Speed

[Auto]

Use the

Speed

option to configure the PCIe Mini card and PCIe x1 slot speed.

Auto

EFAULT

Gen

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands