IEI Technology eKINO-BT User Manual Download

Page: 71 / 157

eKINO-BT Mini-ITX SBC

Page 57

4.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during installation may result in

permanent damage to the product and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the eKINO-BT. Dry climates are especially susceptible to ESD. It is therefore

critical to strictly adhere to the following anti-static precautions whenever the eKINO-BT,

or any other electrical component, is handled.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

:- Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: When configuring the eKINO-BT, place it on an

anti-static pad. This reduces the possibility of ESD damaging the eKINO-BT.

Only handle the edges of the PCB

:-: When handling the PCB, hold it by the

edges.

4.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should

be read and understood before the eKINO-BT is installed. All

installation notices pertaining to the installation of eKINO-BT should be

strictly adhered to. Failing to adhere to these precautions may lead to

severe damage of the eKINO-BT and injury to the person installing the

motherboard.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands