IEI Technology eKINO-BT User Manual Download

Page: 117 / 157

eKINO-BT Mini-ITX SBC

Page 103

5.3.8 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 13

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

Configuration

Security Device Support

[Disable]

Current Status Information

NO Security Device Found

Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.

----------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 13: Trusted Computing

Security Device Support [Disable]

Use the

Security Device Support

option to configure support for the TPM.

Disable D

EFAULT

TPM support is disabled.

Enable

TPM support is enabled.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands