IEI Technology eKINO-BT User Manual Download

Page: 127 / 157

eKINO-BT Mini-ITX SBC

Page 113

Main

Advanced

Chipset

Security

Boot

Save & Exit

Save Changes and Reset

Discard Changes and Reset

Restore Defaults
Save as User Defaults
Restore User Defaults

Reset the system after
saving the changes.

---------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 22: Save & Exit

Save Changes and Reset

Use the

Save Changes and Reset

option to save the changes made to the BIOS options

and reset the system.

Discard Changes and Reset

Use the

Discard Changes and Reset

option to exit the system without saving the

changes made to the BIOS configuration setup program.

Restore

Defaults

Use the

Restore Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F3 key can be used for this operation.

Save as User Defaults

Use the

Save as User Defaults

option to save the changes done so far as user defaults.

Restore User Defaults

Use the

Restore User Defaults

option to restore the user defaults to all the setup options.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands