![background image](http://html2.mh-extra.com/html/icom/ic-905/ic-905_basic-manual_4941549012.webp)
xi
BASIC MANUAL
R
DANGER HIGH RF VOLTAGE! NEVER
touch an
antenna, an antenna connector, or a ground terminal
while transmitting. This could cause an electrical
shock or burn.
R
DANGER! NEVER
operate the transceiver near
unshielded electrical blasting caps or in an explosive
atmosphere. This could cause an explosion and
death.
R
WARNING RF EXPOSURE!
This transceiver
emits Radio Frequency (RF) energy. Extreme caution
should be observed when operating this transceiver.
If you have any questions regarding RF exposure
and safety standards please refer to the Federal
Communications Commission Office of Engineering
and Technology’s report on Evaluating Compliance
with FCC Guidelines for Human Radio Frequency
Electromagnetic Fields (OET Bulletin 65).
R
WARNING! NEVER
operate the transceiver with
earphone, a headset, or other audio accessories at
high volume levels. If you experience a ringing in your
ears, reduce the volume or discontinue use.
R
WARNING! NEVER
apply AC power to the [DC
13.8 V] jack on the controller side panel. This could
cause a fire or damage the transceiver.
R
WARNING! NEVER
apply more than 16 V DC to
the [DC 13.8 V] jack on the controller side panel. This
could cause a fire or damage the transceiver.
R
WARNING! NEVER
reverse the DC power cable
polarity. This could cause a fire or damage the
transceiver.
R
WARNING! NEVER
remove the fuse holder on the
DC power cable. Excessive current caused by a short
could cause a fire or damage the transceiver.
R
WARNING! NEVER
let metal, wire or other objects
contact the inside of the transceiver, or make incorrect
contact with connectors on the side panel. This could
cause an electric shock or damage the transceiver.
R
WARNING! NEVER
operate or touch the
transceiver with wet hands. This could cause an
electric shock or damage to the transceiver.
R
WARNING! NEVER
operate the equipment if
you notice an abnormal odor, sound or smoke.
Immediately turn OFF the power and/or remove
the DC power cable. Contact your Icom dealer or
distributor for advice.
R
WARNING! NEVER
put the transceiver on an
unstable place where the transceiver may suddenly
move or fall. This could cause an injury or damage the
transceiver.
R
WARNING! NEVER
operate the transceiver during
a lightning storm. It may result in an electric shock,
cause a fire or damage the transceiver. Always
disconnect the power source and antenna before a
storm.
CAUTION: DO NOT
expose the controller to rain,
snow or any liquids. They could damage the controller.
CAUTION: DO NOT
operate the transceiver unless
the antenna and cables are securely attached to
the transceiver, and that the antenna and cables
are dry before attachment. Exposing the inside of
the transceiver to dust or water will result in serious
damage to the transceiver.
CAUTION: DO NOT
operate the transceiver while
driving a vehicle. Safe driving requires your full
attention—anything less may result in an accident.
CAUTION: DO NOT
change the internal settings
of the transceiver. This could reduce transceiver
performance and/or damage to the transceiver. The
transceiver warranty does not cover any problems
caused by unauthorized internal adjustments.
CAUTION: DO NOT
install or place the transceiver in
a place without adequate ventilation. Heat dissipation
may be reduced and damage the transceiver.
CAUTION: DO NOT
use harsh solvents such as
Benzine or alcohol when cleaning. This could damage
the transceiver surfaces. If the surface becomes dusty
or dirty, wipe it clean with a soft, dry cloth.
CAUTION: DO NOT
leave the transceiver in areas
with out of the specified temperature range for the
controller (0°C ~ 50°C, 32°F ~ 122°F) and the RF unit
(–10°C ~ +55°C, 14°F ~ 131°F) for mobile operations.
CAUTION: DO NOT
place the transceiver in
excessively dusty environments. This could damage
the transceiver.
CAUTION: DO NOT
place the transceiver against
walls or putting anything around the transceiver. This
may overheat the transceiver.
CAUTION: DO NOT
set the transceiver’s RF output
power to more than a connected linear amplifier’s
maximum input level. Otherwise, the linear amplifier
will be damaged.
CAUTION: DO NOT
use non-Icom microphones.
Other microphones have different pin assignments,
and may damage the transceiver.
PRECAUTIONS