![background image](http://html2.mh-extra.com/html/icom/ic-905/ic-905_basic-manual_4941549069.webp)
8-15
BASIC MANUAL
SET MODE
8
8
» SET > Connectors >
SEND Output
144M
(Default: ON)
430M
(Default: ON)
1200M
(Default: ON)
2400M
(Default: ON)
5600M
(Default: ON)
10G
(Default: ON)
Selects whether or not to switch the SEND terminal
output level of the controller’s [SEND] jack and the RF
unit’s [ACC] socket (SEND pin) to the Low level when
transmitting.
•
OFF: Does not switch to Low level.
• ON: Switches to Low level.
» SET > Connectors >
USB SEND/Keying
TIP:
This is the setting for the terminal used for data
communication when you operate the transceiver
using software on a PC.
When you connect the transceiver to the PC with a
USB cable, 2 COM ports are recognized on the PC.
To confirm USB (A)/USB (B), open the COM port
properties, and confirm the “Value” on the “Details”
tab.
USB SEND
(Default: OFF)
Sets the USB terminal of the controller to receive the
SEND signal from the software on the PC. Select the
same terminal as the terminal set by the software.
L
You cannot select the terminal which is already selected
in the “USB Keying (CW)” or “USB Keying (RTTY)” item.
USB Keying (CW)
(Default: OFF)
Sets the USB terminal of the controller to receive the
CW Keying signal from the software on the PC. Select
the same terminal as the terminal set by the software.
L
You cannot select the terminal which is already selected
in the “USB SEND” or “USB Keying (RTTY)” item.
USB Keying (RTTY)
(Default: OFF)
Sets the USB terminal of the controller to receive the
RTTY Keying signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L
You cannot select the terminal which is already selected
in the “USB SEND” or “USB Keying (CW)” item.
» SET > Connectors >
External Keypad
VOICE
(Default: OFF)
KEYER
(Default: OFF)
RTTY
(Default: OFF)
Enables each memory (voice, keyer, RTTY)
transmission using an external keypad.
» SET > Connectors >
CI-V
CI-V Address
(Default: AC)
Sets the CI-V address in hexadecimal code.
L
“AC” is the default address of the IC-905.
CI-V Transceive
(Default: ON)
Turns the Transceive function ON or OFF.
•
OFF: The status is not output.
• ON: The status is output. When you change a
setting on the transceiver, the same change
is automatically set on other connected
transceivers or receivers, and vice versa.
CI-V USB Echo Back
(Default: OFF)
Turns the Data Echo Back function ON or OFF, when
remotely controlling the IC-905 through the [USB]
CI-V port.
» SET > Connectors >
USB (B) Function
USB (B) Function
(Default: OFF)
The transceiver has 2 virtual COM ports, A and B. In
this item, sets the function to be assigned to USB (B).
L
USB (A) is used for programming, or CI-V operation.
L
When connecting to a USB port on your PC that is
installed the USB driver, USB (A) and USB (B) are named
as “IC-905 Serial Port A (CI-V)” and “IC-905 Serial Port B.”
•
OFF:
Does not assign the function to
USB (B).
• RTTY Decode: Outputs the decoded data of the
RTTY signal.
• DV Data:
Inputs or outputs low speed data for
the DV mode.
• Weather:
Inputs the weather data entries.
GPS Out
(Default: OFF)
Selects whether or not to output the position data to
USB (B).
•
OFF: Does not output the position data to USB (B).
• ON: Outputs the position data to USB (B).
L
It is valid when “USB (B) Function” is set to “OFF” or “DV
Data.”