iCharger 1010B, User Manual

Page: 13 / 22

-13-
iCharger Synchronous Balance Charger/Discharger 1010B/106B
Charge-to-discharge & Discharge-to-charge cycle mode for a Lithium battery
Lithium battery in monitoring mode
When you use other devices to charge or discharge Lithium pack, the iCharger can monitor each cell’s
voltage, battery temperature, charge time and so on, if one of the batteries appears over-charged,
over-discharged, over-hot, over-capacity or over-time ,the
iCharger will alarm with noise “Di…..” and blink
the raleted information.
Charging/discharging cycle mode of Lithium battery.
The left side of the first line shows the type of battery you selected in the
user setup (LiPo,Lilo or LiFe)and the right side shows the cycle number.
The second line shows the cycle direction you selected : (C:x.xxV->D:x.xxV)
or (D:x.xxV->C:x.xxV), the value of the second line sets the final
charge/discharge current. After setting the current and voltage, press
Start/Enter button for more than 3 seconds with a sound ”Di” to start the
next process.
Cycle number: 1 – 10
Voltage: LiPo(3.00 – 4.20V), Lilo(2.50 – 4.10V), LiFe (2.00 – 3.60V)
The number of cells you set and the processor detects. The left side of the
first line ’R:xxSER’ shows the number of cells detected by the
iCharger and
the right side of the first line ’S:xxSER’ is the number of cells set by the user.
If the numbers are different you should make sure that the configured
number and the actual number for the battery are the same and then you
can start charging by pressing
Start/Enter . If not, press Batt type/Stop to
go back to the previous screen and adjust the setting.
Charging/discharging cycle mode of Lithium battery.
In this process, you can stop the cycle at any time by pressing the
Batt
type/Stop button. In the process of C>D or D>C, the blink “C” indicates
charging, while “D” indicates discharging. Press Inc button to display
each cell’s voltage and its past cycling current (see the balance voltage
information& cycling information) and press
Dec button to display the
General Status information.
LiPo LiPo LiPo LiPo MONITOR MONITOR MONITOR MONITOR
3.0V 11.1V(3S)
3.0V 11.1V(3S) 3.0V 11.1V(3S)
3.0V 11.1V(3S)
Monitor mode of Lithium battery. The left side of the first line shows the type
of battery you selected in the
user setup (LiPo,Lilo or LiFe). The value on
the right side of the second line sets the low limit of voltage and the battery
pack number. After setting the current and voltage press
Start/Enter button
for more than 3 seconds with a sound ”Di” to start the next process.
Individual alarm low-Vt: final discharging voltage to the highest
charging voltage (such as: LiPo 3.0V – 4.2V),
Battery series: 1 – 10series (1 – 6 series for 106B)
The monitor information, in this process; you can stop monitoring process at
any timeby pressing
Batt type/Stop button .
Press Inc button to display each cell’s voltage (see the balance voltage
information), the iCharger will alarm with noise “Di….” when any errors
appear.
Start/Enter
>3 seconds
Batt type
stop
R:03SER S:03SER R:03SER S:03SER R:03SER S:03SER R:03SER S:03SER
CONFIRM(ENTER) CONFIRM(ENTER) CONFIRM(ENTER) CONFIRM(ENTER)
Start/Enter
Batt type
stop
Battery
Series
V-BP
Charge
Current
Li03 1.0A 12.60V Li03 1.0A 12.60V Li03 1.0A 12.60V Li03 1.0A 12.60V
C>D 00993 059 C>D 00993 059 C>D 00993 059 C>D 00993 059: : : :51 51 51 51
battery
voltage
number
of cells
cycle
capacity
cycle
time
cycle
current
work
state
Start/Enter
>3 seconds
Batt type
stop
Battery
Series
V-BP
Charge
Current
Li03 50
Li03 50 Li03 50
Li03 50℃
℃ ℃
℃ 12.60V
12.60V 12.60V
12.60V
Monitor 050 Monitor 050 Monitor 050 Monitor 050: : : :43 43 43 43
battery
voltage
number
of cells
run
time
Ext.
temperature
work
state
LiPo CYCLE 3 LiPo CYCLE 3 LiPo CYCLE 3 LiPo CYCLE 3
C:4.20V
C:4.20V C:4.20V
C:4.20V-
- -
->D:3.00V
>D:3.00V >D:3.00V
>D:3.00V
-
Dec
+
Inc
-
Dec
+
Inc
-
Dec
+
Inc
-
Dec
+
Inc