iCharger 1010B, User Manual

Page: 14 / 22

-14-
iCharger Synchronous Balance Charger/Discharger 1010B/106B
Pre-charging a Lithium battery
If the battery is over-discharged and the voltage is too low then in the Normal charge or Fast charge modes
the
iCharger will notify the user of pre-charging with a low current (100mA). This helps to increase the
battery voltage to the within the allowable range for normal charging. The user can set the pre-charging time
in the
Lithium Check time screen in the User setup.
General Status information
This information can be accessed by pressing Dec while charging is active.
General Status Information Voltage of Balance Port
Inc
1:4.01 4.03 4.07 1:4.01 4.03 4.07 1:4.01 4.03 4.07 1:4.01 4.03 4.07
4:4.02 4.05 4.04
4:4.02 4.05 4.04 4:4.02 4.05 4.04
4:4.02 4.05 4.04
End Voltage End Voltage End Voltage End Voltage
16.80V
16.80V 16.80V
16.80V
Input power Input power Input power Input power
Voltage Voltage Voltage Voltage 11.80V 11.80V 11.80V 11.80V
Ext.Temp 30 Ext.Temp 30 Ext.Temp 30 Ext.Temp 30℃ ℃ ℃ ℃
Int.Temp
Int.Temp Int.Temp
Int.Temp 40
40 40
40℃
℃ ℃
℃
Capacity Cut Capacity Cut Capacity Cut Capacity Cut- - - -Off Off Off Off
ON 5000mAh
ON 5000mAh ON 5000mAh
ON 5000mAh
Safety timer Safety timer Safety timer Safety timer
ON 12
ON 12 ON 12
ON 120min
0min 0min
0min
Temp Cut Temp Cut Temp Cut Temp Cut- - - -Off Off Off Off
OFF 50
OFF 50 OFF 50
OFF 50℃
℃ ℃
℃
Dec
Dec
Dec
Dec
Dec
Dec
Inc
7:4.01 4.03 4.07 7:4.01 4.03 4.07 7:4.01 4.03 4.07 7:4.01 4.03 4.07
A:4.02 A:4.02 A:4.02 A:4.02
Inc
CHG 1 00213mAh
CHG 1 00213mAh CHG 1 00213mAh
CHG 1 00213mAh
DCHG 1 00199mAh DCHG 1 00199mAh DCHG 1 00199mAh DCHG 1 00199mAh
CHG 2 00203mAh
CHG 2 00203mAh CHG 2 00203mAh
CHG 2 00203mAh
DCHG 2 00197mAh DCHG 2 00197mAh DCHG 2 00197mAh DCHG 2 00197mAh
Inc
。。。
。。。 。。。
。。。
（
not for 106B
）
Cycle Information
The following screen is displayed when the charger detects the battery
voltage to be too low in the Normal charge or Fast charge modes.
Pre-charge lithium battery. Press
Start/Enter to start the charging process
or press Stop to go back to the previous screen.
Status display. The left side of the first line shows the type of battery you
selected in the
User setup (LiPo, Lilo or LiFe) and number of cells
detected. In the middle is the pre-charge current (100mA). On the right is
the voltage of the battery pack. The second line shows the charging
progress with capacity charged (mAh) and charging time. The charger will
switch back to the configured charge mode when the pre-charge time limit
is reached. You can stop the pre-charging process at any time by pressing
the
Batt type/Stop button.
Do checking? Do checking? Do checking? Do checking?
CONFIRM(ENTER) CONFIRM(ENTER) CONFIRM(ENTER) CONFIRM(ENTER)
Li03 0.1A 12.40V
Li03 0.1A 12.40V Li03 0.1A 12.40V
Li03 0.1A 12.40V
CHK 00001 000 CHK 00001 000 CHK 00001 000 CHK 00001 000: : : :51 51 51 51
battery of
cells test
online
charged
capacity
charging
time
0.1A
pre-charge
current
battery
voltage
work
state
Pre-charging battery
Start/Enter
Batt type
stop