IBM Power 730 Express 8231-E2B Manual Download Page 24

Page: 24 / 112

24.

Remove the power interlock switch. For instructions, see Removing the 8231-E2B, 8231-E1C,
8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D power interlock switch with the power off.

25.

Remove the vital product data card. For instructions, see Removing the 8231-E2B, 8231-E1C,
8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D vital product data card.

26.

Remove the storage interposer card. For instructions, see Removing the 8231-E2B, 8231-E1C,
8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D storage interposer card with the power off.

27.

Remove the second voltage regulator module, if present. For instructions, see Removing the
8231-E2B, 8231-E1C, 8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D voltage regulator module.

28.

Remove the metal guide bracket for the second voltage regulator module:

Remove the two screws securing the bracket to the chassis.

Lift the bracket from the chassis.

29.

Remove the middle fan cage. For instructions, see Removing the 8231-E2B, 8231-E1C, 8231-E1D,
8231-E2C, 8231-E2D, or 8268-E1D middle fan cage.

30.

Remove the system processor modules. For instructions, see Removing the 8231-E2B, 8231-E1C,
8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D system processor module.

31.

Remove the system backplane.

Note:

Use care when removing the system backplane. Do not lift the system backplane by any of

the attached modules.

Remove the screws (A). See Figure 9 on page 13 or Figure 10 on page 13.

Note:

Do not remove any of the Torx screws. Remove only the five hex and slot combination

screws.

Figure 8. Removing the front fan cable

Power Systems: System backplane for the 8231-E2B, 8231-E1C, 8231-E1D, 8231-E2C, 8231-E2D, or 8268-E1D

Summary of Contents for Power 730 Express 8231-E2B

















































































































Search results

Summary of Contents for Power 730 Express 8231-E2B

Reviews:

Related manuals for Power 730 Express 8231-E2B

Brands by name

Popular brands

IBM Power 730 Express 8231-E2B, Manual

Search results

Summary of Contents for Power 730 Express 8231-E2B

Reviews:

Related manuals for Power 730 Express 8231-E2B

Brands by name

Popular brands