IBM Infoprint 1130 Service Manual Download Page 61 | Manualshive

Page: 61 / 433

background image

2-34

Service Manual

IBM Infoprint 1130/1140

36 Resolution
Reduced

The resolution of the page has been
reduced from 600 dpi to 300 dpi to
prevent a Memory Full error. This
message can only occur if the
Resolution Reduction setting is turned
on.

Note: 1200 dpi pages are not resolution
reduced. If a 1200 dpi job runs out of
memory, a Memory Full error is
displayed.

37 Insufficient
Collation Memory

This message is displayed when the
printer memory used to store pages is
too full to collate the print job.

38 Memory Full

This message is displayed when the
printer memory used to store pages is
full.

39 Complex Page

This message is displayed when the
page is too complex to print.

51 Defective Flash

This message is displayed when the
printer detects a defective flash. This
error may occur at power on, or during
flash format and write operations. Press
Go to clear the message. The flash is
marked as bad and normal operation
continues. Flash operations are not
allowed until the problem is resolved.

52 Flash Full

This message is displayed when there is
not enough free space in the flash
memory to hold the resources that have
been requested to be written to flash.

53 Unformatted
Flash

This message is displayed when the
printer detects an unformatted flash at
power on. Press Go to clear the
message. The flash is marked as bad
and normal operation continues. Flash
operations are not allowed until the flash
is formatted.

User Message
Primary

User
Message
Secondary

Explanation

«
...
59
60
61
62
63
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Infoprint 1130

Brand: Oki Pages: 8

Brand: Oki Pages: 48

Stylus Pro 7900

Brand: X-Rite Pages: 36

Brand: Oki Pages: 16

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 8

KX-FLB851 - All-in-One Flatbed Laser Fax

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

CLP-680ND: CLP-775ND

Brand: Samsung Pages: 2

Brand: EBS Pages: 34

Brand: Canon Pages: 32

VersaCamm SP-300V

Brand: Roland Pages: 4

Brand: VuPoint Pages: 20

Brand: SANEI ELECTRIC Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands