Home
/
IBM
/
Infoprint 1130
/
Service Manual

IBM Infoprint 1130, Service Manual

Share

Page: 138 / 433

IBM Infoprint 1130 Service Manual Download Page 138

Diagnostic Information

2-111

IBM Infoprint 1130/1140

2

High Voltage Contact

Check the PC drum contact on the
right side frame for damage, PC
drum contact wear or contamination.
If the contact is bent or damaged,
replace the contact.

Note: Inspect the HVPS PC drum
contact on the board for any signs of
damage or contamination.

3

HVPS

Check the fuse on the HVPS. If
open, replace the HVPS. Check the
voltages at J25 on the system board.
Measure the following voltages from
connector J25 to printer ground:

Printer Idle
J25-5 me24 V dc

Printer Printing
J25-5 me24 V dc

In the voltages at J25-5 are
incorrect, replace the system board.

4

Front Cable Harness
HVPS Section

Check the front cable harness at J25
on the system board and at CN1 on
the HVPS to make sure the harness
is connected properly. If connected
properly, check the continuity of the
cable harness. If there is no
continuity, replace the front cable
harness.

5

Printhead Assembly

Generally a 93x service error is
posted if the printhead assembly
fails and the printer does not give a
blank copy symptom.

The printhead used in the printer
does not have a mechanical shutter
as previous laser printers. The
printer is interlocked through the
front top cover interlock switch.

FRU

Action

«
...
136
137
138
139
140
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands