manualshive.com logo in svg

IBM Infoprint 1130, Service Manual

Share
Download
IBM Infoprint 1130 Service Manual Download Page 122

Diagnostic Information

2-95

IBM Infoprint 1130/1140

990 Service - BIN X

FRU

Action

1

D.C. Motor
Mechanical Linkage 
Assembly

Check the DC motor cable 
connector to be sure it is correctly 
installed at J4 on the output 
expander option board. If correct, 
disconnect J4 from the option 
board and check the resistance of 
the motor on the cable connector: 
J4-1 to J4-2: measures between 
115 and 135 ohms. Also check J4-
1 and J4-2 to the motor case for 
shorts. If either the resistance is 
incorrect or a short is found, 
replace the motor/mechanical 
linkage assembly.
Note: If the DC motor is shorted, it 
may also be necessary to replace 
the control board.

2

Output Expander Control 
Board 

Disconnect the motor cable J4 
and check the voltages at J4 on 
the board.

Note: Use caution not to short to 
adjacent pins on the connector. 

J4-1 (Motor Idle) +24 V dc
J4-2 (Motor Idle) +24 V dc
J4-5 (Motor Idle) +5 V dc
J4-6 (Motor Idle) +5 V dc

If any of the voltages are 
incorrect, replace the control 
board. If the voltages are correct, 
replace the DC motor/mechanical 
linkage assembly.

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands