IBM Infoprint 1130 Service Manual Download Page 67 | Manualshive

Page: 67 / 433

IBM Infoprint 1130 Service Manual Download Page 67

2-40

Service Manual

IBM Infoprint 1130/1140

The messages in the following table can occur in two ways. The
specified device could have been removed from the printer, for
instance to clear a paper jam. Otherwise, the device can still be
attached to the printer, but is experiencing a communications
problem, not fully connected, or having a hardware failure.

•

If the device is temporarily removed or not connected properly,
then reattach it. When the option is recognized, the printer
automatically clears the error and continues.

•

If the option is experiencing a hardware problem, turn the
printer off and back on. If the error occurs again, turn the printer
off, remove the option and call for service.

User Status Message

Explanation

Turn Printer OFF to
Enable Option

This message displays when a printer option,
Input Tray, Output Bin or Envelope Feeder, has
been attached while the printer is powered On. To
use the option, the printer must first be powered
off and back on again. Data loss results if print
jobs are active when the printer is power cycled. If
a print job is active, then remove the option and
finish the job. The printer automatically clears the
message once the option is removed. Once the
job is complete, turn off the printer and attach the
option again.

Insert Duplex Front
Cover

This message displays when the duplex front
access cover is not installed.

Close Duplex Rear Door

This message displays when the duplex rear door
is open.

«
...
65
66
67
68
69
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands