manualshive.com logo in svg

IBM Infoprint 1130, Service Manual

Share
Download
IBM Infoprint 1130 Service Manual Download Page 185

3-20

Service Manual

IBM Infoprint 1130/1140

The multipurpose tray and the envelope feeder do not have a paper 
low sensor. The multipurpose tray does not have a pass thru sensor.

The following tray sensors are supported by this test:

Output Bin - Feed to all Bins Test

This test can be used to verify that the printer can feed media to the 
standard bin or any installed output options. No information will be 
printed on the test pages as the printhead is not turned on during the 
feed test.

To run the Feed to all Bins Test:

1. Select Feed to all Bins Test from the Menu.

2. The media feeds from the default paper source.

3. The printer feeds a separate piece of media to the standard bin 

first, then it feeds a separate piece of media to each output bin 
installed in the following order:
First Sheet: Standard Bin, Second Sheet: Bin #1, Third Sheet: 
Bin #2, Fourth Sheet: Bin #3, Fifth Sheet: Bin #4, Sixth Sheet: 
Bin #5, Seventh Sheet: Bin #6, Eighth Sheet: Bin #7, Ninth 
Sheet: Bin #8, Tenth Sheet: Bin #9, Eleventh Sheet: Bin #10, 

Source

Tray Empty 
Sensor

Paper Low 
Sensor

Pass Thru 
Sensor

Tray 1

YES

YES

NO

Tray 2

YES

YES

YES

Tray 3

YES

YES

YES

Tray 4

YES

YES

YES

Tray 5

YES

YES

YES

Multipurpose 
Tray

YES

NO

NO

Envelope Feeder

YES

NO

YES

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands