manualshive.com logo in svg

IBM Infoprint 1130, Service Manual

Share
Download
IBM Infoprint 1130 Service Manual Download Page 76

Diagnostic Information

2-49

IBM Infoprint 1130/1140

Cover Open Switch/Cable Service Check

FRU

Action

1

Toner Cartridge

Check the toner cartridge to make 
sure it is correctly installed and that 
the right and left cartridge tracks are 
not loose or broken. Check to make 
sure the cover open switch 
activation tab on the toner cartridge 
is not broken and that the tab 
correctly activates the cover open 
switch spring.

2

Cover Open Switch/Cable 
Assembly

Check the cover open switch for 
proper mechanical operation. If 
incorrect, repair as necessary. 
Disconnect the cover open switch 
cable from J3 at the system board 
and measure the voltage at J4-3. It 
measures approxi5 V dc. If 
the voltage is incorrect, replace the 
system board. If the voltage is 
correct, check the voltage at J3-1. If 
the voltage measures greater than 
+1.0 V dc, replace the system board. 
If the voltage is correct, check the 
continuity between J3-1 and J3-3 on 
the cable. If no change in continuity 
occurs as the switch is activated, 
replace the cover open switch/cable 
assembly. If the continuity changes 
as the switch is activated, replace 
the system board.

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands