manualshive.com logo in svg

IBM Infoprint 1130, Service Manual

Share
Download
IBM Infoprint 1130 Service Manual Download Page 121

2-94

Service Manual

IBM Infoprint 1130/1140

Remove Paper - Output Bin X is displayed, POST incomplete, 
unable to clear the message.

271 Paper Jam - Check Bin X, POST incomplete

271 Paper Jam - Check Bin X, POST complete, first sheet of paper 
feeds into Output Bin X.

Note:  Before performing the following checks run the Output Bin X 
Sensor Test and check for the failing sensor.

Sensor Test: NF = Near Full (Upper part of sensor assembly)

F = Full (Lower part of sensor assembly)

P = Pass Thru Sensor

FRU

Action

1

Dual Output Bin Sensor Flag

Check the flag for correct 
operation, binding, broken parts or 
interference from the sensor 
cable, If incorrect, repair as 
necessary.

FRU

Action

1

Pass Thru Sensor and Flag 
Assembly
Control Board

Check the sensor flag for proper 
operation. If correct, check to 
make sure the pass thru sensor 
cable is correctly connected to J3 
on the control board. Disconnect 
the pass thru sensor cable from 
J3 on the control board and check 
the voltage at J3-3. The voltage 
measures approxi5 V dc. 
If incorrect, replace the control 
board. If correct, check the 
voltage at J3-2. The voltage 
measures approximately 0 V dc. If 
incorrect, replace the sensor 
assembly. If this does not fix the 
problem, replace the control 
board.

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands