IBM Infoprint 1130 Service Manual Download Page 1 | Manualshive

Page: 1 / 433

background image

Edition: May 2001

The following paragraph does not apply to any country where such provisions are
inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do
not allow disclaimer of express or implied warranties in certain transactions; therefore,
this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes
are periodically made to the information herein; these changes will be incorporated in
later editions. Improvements or changes in the products or the programs described may
be made at any time.

Comments may be addressed to Lexmark International, Inc., Department D22A/032-2,
740 West New Circle Road, Lexington, Kentucky 40550, U.S.A or e-mail at
[email protected]. Lexmark may use or distribute any of the
information you supply in any way it believes appropriate without incurring any obligation
to you. You can purchase additional copies of publications related to this product by
calling 1-800-553-9727. In other countries, contact your point of purchase.

ImageQuick, Optra Forms, PictureGrade and StapleSmart are trademarks of Lexmark
International, Inc.

Lexmark and Lexmark with diamond design, Prebate and MarkNet are trademarks of
Lexmark International, Inc., registered in the United States and/or other countries.

PostScript is a registered trademark of Adobe Systems Incorporated.

PCL is a registered trademark of the Hewlett-Packard Company.

Other trademarks are the property of their respective owners.

© Copyright Lexmark International, Inc. 2001.
All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS
This software and documentation are provided with RESTRICTED RIGHTS. Use,
duplication or disclosure by the Government is subject to restrictions as set forth in
subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc.,
Lexington, KY 40550.

IBM Infoprint 1130 and 1140

P/N: 12G3959

1
2
3
...
»

Summary of Contents for Infoprint 1130


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Infoprint 1130

Brand: NCR Pages: 10

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 858

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 4

Brand: 3Doodler Pages: 8

Brand: VASTEX Pages: 2

Brand: OKIDATA Pages: 13

Brand: Xerox Pages: 205

Brand: Star Pages: 82

Brand: Kyocera Pages: 2

Brand: A&D Pages: 66

Brand: Oki Pages: 187

Brand: Oki Pages: 204

7400DN - Phaser Color LED Printer

Brand: Xerox Pages: 3

Brand: Mayku Pages: 2

Brand: Seiko Epson Pages: 301

Brand: Canon Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands