![background image](http://html2.mh-extra.com/html/ibm/8265-nways-atm-switch/8265-nways-atm-switch_problem-determination-and-service-manual_3312418092.webp)
MAP 0460 (continued)
006 (continued)
When different modules are reset, one after the other and become isolated, the problem cause is
frequently on the CPSW module.
– Browse the 8265 error log and look for a set of messages similar to the following for each concerned
module.
'775 1ð|ð3 11:59:35 atmehbld.c-914
E EH
Hard minor ðð_ðð32_EH POLL
CELL NOT
RECEIVED Poll cell not received when processing blade 13
776 1ð|ð3 11:59:37 atmcspol.c-329
E CS
Soft minor ð5_2ð43_CS Poll
response missing.
Cause slot 13 (no_resp=1), poll timer is now 3ððð ms (was 25ðð or 3ððð)
777 1ð|ð3 11:59:42 atmehbld.c-914
E EH
Hard minor ðð_ðð32_EH POLL
CELL NOT RECEIVED Poll cell not received when processing blade 13
778 1ð|ð3 11:59:49 atmehbld.c-914
E EH
Hard minor ðð_ðð32_EH POLL
CELL NOT RECEIVED Poll cell not received when processing blade 13
78ð 1ð|ð3 11:59:55 atmehbld.c-914
E EH
Hard minor ðð_ðð32_EH POLL
CELL NOT RECEIVED Poll cell not received when processing blade 13
781 1ð|ð3 12:ðð:ð2 atmehbld.c-914
E EH
Hard minor ðð_ðð32_EH POLL
CELL NOT RECEIVED Poll cell not received when processing blade 13
782 1ð|ð3 12:ðð:ð2 atmehbld.c-723
E EH
Hard MAJOR ðð_ðð21_EH TOO
MANY RESETS Too many unsuccessful resets (4) for blade 13.
783 1ð|ð3 12:ðð:ð2 atmehbld.c-1125
E EH
Hard MAJOR ðð_ðð23_EH ISOLATION
REQUESTED Blade 13: unsuccessful recovery isolation required'
If you can see this, then go to “MAP 0210: CPSW/CPSW2 in Maintenance Mode” on page 2-23 for
CPSW related problems.
007
– Verify the port activity LEDs of the failing module.
Is there at least one LED permanently ON?
Yes No
008
– Perform the LED test to ensure that the modules LED are OK.
Is at least one activity LED burned?
Yes No
009
If the LEDs are OK, the modules hardware level is suspected to be bad: To check this and
get information on hardware update, go to “Compatibility Problems between Hardware and
Microcode Module Levels” on page 2-68.
– If the problem persists (after a module upgrade) or the module is already at the latest
hardware level, enter:
set port <slot.port1 port2.. portn> disable then wrap<slot.all>internal commands.
Did you receive at least one message stating that the test failed?
Yes No
010
(Step 010 continues)
2-60
8265 PD and SG
Summary of Contents for 8265 Nways ATM Switch
