![background image](http://html2.mh-extra.com/html/ibm/8265-nways-atm-switch/8265-nways-atm-switch_problem-determination-and-service-manual_3312418119.webp)
2.
save all
3.
reset atm_subsystem
4. Log on as the Administrator on the A-CPSW console
Swapping
Do not perform any swap before downloading the:
1. Operational code
2. FPGA code
3. Boot code
The hub will reset and the backup CPSW will become active. Go to Step 2.
STEP 6. Activate the new FPGA picocode and new A-CPSW microcode.
1. Activate the new version of A-CPSW FPGA picocode by entering the command :
a.
save all
b.
swap fpga_picocode 9 or 11
The Telnet session (if existing) is broken. Logon as Administrator on the A-CPSW console.
2. Activate the new version of the A-CPSW microcode by entering the command:
swap microcode
3. Confirm with
Y.
4. If you do not have redundant A-CPSW, go to Step 7.
If you have already swapped new FPGA picocode and microcode on both A-CPSW modules go to
Step 7.
Verify the new levels of codes:
–
show device
–
show module n verbose
By entering the following, the A-CPSW will become secondary (as it was before the beginning of the
download operation):
1.
set device role secondary
2.
save all
3.
reset atm_subsystem
4. The hub will reset and the back-up A-CPSW will become active
5. Perform the Step 6 again on the other A-CPSW
STEP 7. Check the new levels of code:
1.
show device
2.
show module n verbose
When a PCMCIA card is installed as a Release Vehicle, the following steps must be followed. Do not
reset the 8265 during all these phases until
Press Enter and 8265 password required are displayed.
1. If the A-CPSW boot code is different from the one located on the PCMCIA card, UPDB is
displayed on the CPSW display. This means that the flash boot EEPROM (ZM36) on the control
point card is updated with the boot code based on the PCMCIA card.
2. Once the boot updated phase is completed, the operational code is loaded on the DRAM. LOAD
is displayed on the CPSW display, then ACTV is displayed.
3. The CPSW FPGA is compared to the one located on the PCMCIA card. The following message
is displayed on the local console:
Chapter 3. Procedures
3-17
Summary of Contents for 8265 Nways ATM Switch
