![background image](http://html2.mh-extra.com/html/ibm/8265-nways-atm-switch/8265-nways-atm-switch_problem-determination-and-service-manual_3312418114.webp)
Upgrading the 8265 by Code Download
The updates for FPGA picocode, boot, and operational microcodes for the 8265 CPSW are available at:
http://www.networking.ibm.com/support/products.nsf/techsupport/(8265)?OpenDocument
Note: See “ESS URL” on page 2-70.
Click on the control point switch module. You have access to IISP code and to PNNI code by entering the
ID and password found in the CPSW Warning Notice shipped with the PNNI PCMCIA card.
The IISP or PNNI zipped package should be placed in a directory, reachable through TFTP (such ase
/tmp for a UNIX/AIX station).
The 8265V332.zip Internet package contains these files (where xxxx indicates if the file applies to IISP or
PNNI):
8265xxxx.RME: This file.
BOOT332.BIN: BOOT A-CPSW microcode V.3.32
xxxxV332.OPE: A-CPSW microcode V.x.xx, where yyyy is PNNI or IISP
FPGA1D12.BIN: A-CPSW FPGA microcode 1D12
REL8265.PDF: Release note for the 8265 current level (Adobe PDF file).
8265v23.MIB: MIB Version 2.3 for CPSW (binary).
In-Band Download Method
Classical IP mode
Ensure that your ATM network is configured for IP Over ATM (RFC 1577). To configure your ATM
network for IP over ATM:
1. Connect an ARP server to the ATM Network. The ARP server will be used to map IP addresses with
ATM addresses.
2. For each A-CPSW module, ensure that the following parameters are configured:
ATM address of the ARP server
IP address and IP mask of the A-CPSW
IP address of the default gateway.
3. Verify the IP connectivity to the ARP server by entering a PING command for each A-CPSW module.
4. Verify the IP connectivity to the TFTP server by entering a PING command for each A-CPSW
module.
5. If under AIX, ensure that the directories and files to download are readable (chmod 777 file_name).
Ethernet or Token Ring LAN-Emulation Mode
Ensure that your network is configured in Ethernet or Token Ring LAN-Emulation mode. To configure
your network in Ethernet or Token Ring LAN-Emulation :
1. You must have an Ethernet or Token Ring LAN-Emulation Server configured and ready.
2. You must configure the Ethernet or Token Ring LAN-Emulation Client on your 8265.
3. You must have a TFTP server somewhere in the IP network (either on the Emulated LAN, or behind
an IP Gateway), and the microcode files installed on that TFTP server.
4. Ensure that you can PING the TFTP server from 8265 LEC.
3-12
8265 PD and SG
Summary of Contents for 8265 Nways ATM Switch
