IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 86 | Manualshive

Page: 86 / 204

IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 86

4.2 Teaching tool connections and testing operation

4-2

4. Operation

4.2 Teaching tool connections and testing operation

A teaching pendant or PC software can be used to test operation or configure data settings. This
manual introduces operating methods using a teaching pendant TB-02.

PC software operating method

PC software manual (ME0155)

Teaching pendant operating method

Teaching pendant manual (ME0355)

Touch panel teaching pendant operation

Touch panel teaching pendant manual

method

(ME0375, ME0376)

Caution

Maximum stroke operation is configured at shipping.
Before operating the ELECYLINDER, make sure to check there is nothing that will
interfere with moving parts within the operation range.

Teaching pendant connection

Connect the teaching pendant/TB-02 while the power is OFF.
Insert the round connector of TB-02 to the SIO port of the ELECYLINDER.

Turn ON the 24VDC power supply.

TB-02 will start up and the Menu screen
will be displayed.

1

2

Action

Reference

[TB-02]

Insert the round
connector with arrow
mark downward

SIO port

«
...
84
85
86
87
88
...
»

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Reviews:

No comments