manualshive.com logo in svg

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 112 / 204

Share
Download
IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 112

 

6.2 How to change parameters 

6-2 

6. Parameter

s 

6.2  How to change parameters 

 
A teaching pendant or PC software can be used to change parameters. This manual introduces 
operating methods using a teaching pendant TB-02. 

 

 
PC software operating method 

PC software manual (ME0155) 

Teaching pendant operating method 

Teaching pendant manual (ME0355) 

Touch panel teaching pendant operation 

Touch panel teaching pendant manual 

method   

(ME0375, ME0376) 

 

 

Edit parameters window 

 

Touch Parameter edit on the Menu 1 screen.   
 

The screen will switch to the Edit parameters   
window. 
If the TP operation mode is not Monitor mode, 
a confirmation window will appear for 
switching to Monitor mode. 
Also, if the parameter edit password is set to a   
value other than "0000", the password input screen will be displayed. 

 

If the parameter edit password is set to a value other 
than "0000", enter the password and press the [ENT] 
key on the touch panel. 
 

The Edit parameters window will open. 

 
 

 

The parameter edit password is set to "0000" at shipping. 
Refer to the Teaching pendant manual (ME0355) / Touch panel teaching   
pendant manual (ME0375, ME0376) for information about changing the   
password. 
 

 

1 

Action 

2 

Reference 

Action 

Reference 

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Reviews:

No comments