manualshive.com logo in svg

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 151 / 204

Share
Download
IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 151

 

8.3 Visual inspection items 

8-5 

8. Maintenan

ce and Inspection 

 
Refer to "8.5 Greasing method" for detailed information about the greasing method. 
Refer to "8.6 How to replace components" for detailed information about specific component 
replacement and adjustment methods. 
 

Internal visual inspection 

 

 

Inspection items 

Maintenance work 

Is play or dust generated? 

The guide may be damaged. 
Contact IAI. 

Has foreign matter penetrated inside? 

Remove the foreign matter, clean, and inspect the 
interior for any damage. 

Is the guide grease not lubricating well?
(Even if the grease is brown, 
lubrication is adequate if the running 
surface is shiny) 

Wipe away the old grease, 
then replenish with new grease. 
 
 

Is dust or foreign matter adhered to 
the guide? 

Replenish with new grease after cleaning. 
 

 

 

 

 

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Reviews:

No comments