IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 161

Page: 161 / 204

8.6 How to replace components

8-15

8. Maintenan

ce and Inspection

Controller replacement (motor cover assembly replacement)

(1) Loosen the screws and remove the end cover.
(2) Loosen the screws to remove the wiring/connectors, then remove the used

motor cover assembly.

→ Refer to "Precautions for connectors/wiring" on page 8-16.

(3) Mount the wiring/connectors to the new motor cover assembly and return it to

the original state.

(4) Mount the end cover.

How to replace the

motor cover assembly

Motor cover assembly bottom plate

Cross-recessed tapping screws × 2 pcs
(M3 × 10, Tightening torque 0.60N

•

End cover

Cross-recessed pan screws × 2 pcs
B6/B7: M3 × 110/150,
Tightening torque 0.60N

•

(M3×150/200 for models with brake)
(Pan screws × 2 pcs)

Motor cover assembly

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Search results

Summary of Contents for EYECYLINDER EC-B6 Series

Reviews:

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 161 / 204

Search results

Summary of Contents for EYECYLINDER EC-B6 Series

Reviews: