manualshive.com logo in svg

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 106 / 204

Share
Download
IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 106

 

5.3 Setting maintenance information 

5-4 

5. Preventive

/Predi

ctive Maintenance

 

5.3  Setting maintenance information 

 

The maintenance information can be configured and changed using the teaching pendant or PC 
software. This manual introduces operating methods using a teaching pendant TB-02. 

 

 
PC software operating method 

PC software manual (ME0155) 

Teaching pendant operating method 

Teaching pendant manual (ME0355) 

Touch panel teaching pendant operation 

Touch panel teaching pendant manual 

method   

(ME0375, ME0376) 

 

 

Switching to maintenance information window 

 

Touch "Information" on the Menu 1 screen. 
 

The screen will switch to the Information   
window. 
If the TP operation mode is not Monitor mode, 
a confirmation window will appear for   
switching to Monitor mode. 

 

 
 

Touch "Maintenance information" on the   
Information screen. 
 

     

The maintenance information window opens.

 

 

 
 

 

1 

Action 

2 

Action 

Reference 

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Reviews:

No comments