IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 139

Page: 139 / 204

7.4 Troubleshooting by alarm groups

7-13

Troubleshooting

Alarm group C: Controller abnormality alarm

Controller abnormality occurred.

No.

Cause

Countermeasure

The controller is affected by the noise of a peripheral
device and cannot operate normally.

Shut down the power supply of the peripheral device
and operate only

with the ELECYLINDER, then

check to see whether this alarm persists.
If it does not, there is a possibility that the
ELECYLINDER

is affected by the noise from the

peripheral device.
Reconsider the noise countermeasures (grounding,
power line wiring, electrostatic shielding, etc.) for the
peripheral device.

If this alarm recurs after performing the inspection
above and improving the power supply environment,
it is highly likely that the controller has failed.

Replace the controller cover assembly.

→For details, refer to "

Controller replacement

(page 8-15 to 16)".

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Search results

Summary of Contents for EYECYLINDER EC-B6 Series

Reviews:

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 139 / 204

Search results

Summary of Contents for EYECYLINDER EC-B6 Series

Reviews: