manualshive.com logo in svg

IAI EYECYLINDER EC-B6 Series, Instruction Manual, Page: 190 / 204

Share
Download
IAI EYECYLINDER EC-B6 Series Instruction Manual Download Page 190

 
10.1 Concept of life for belt type 

10-2 

10. Life 

 
For "Standard load coefficient fws", "Load coefficient fw" and "Mounting coefficient fα",   
refer to the contents below for configuration and selection. 

 

[Standard load coefficient fws] 

For ELECYLINDERs described in this manual, calculate with fws = 1.2. 

 

[Load coefficient fw] 

This coefficient allows consideration of the effects on life due to operating conditions. 

 

Load 

coefficient fw 

Operating conditions 

Guideline for 

acceleration/deceleration 

1.0 to 1.5 

Low vibration/impact, slow operation 

1.0G or less 

 

[Mounting coefficient fα] 

This coefficient allows consideration of the effects on life due to ELECYLINDER mounting 
status. 

 

Mounting 
coefficient fα 

1.0 

1.2 

1.5 

Mounting 

status 

Fixed on entire 

surface 

Fixed at both ends 

Fixed locally 

 

 

 
 

● The actuator used in the explanatory figures above is not the ELECYLINDER. 

Replace with ELECYLINDER and select the mounting coefficient. 

● Even when seated over the total length of the product, select 1.2 or 1.5 for the   

mounting coefficient depending on the position of screw fixing and not "fixing over the 
entire surface". 

● Various mounting methods are available for the ELECYLINDER. 

"Fixing over the entire surface" is considered to be the case only when fixing with the 
T-shaped slot and square nut provided on the mounting surface. 

 
 

Summary of Contents for EYECYLINDER EC-B6 Series













































































































































































































Reviews:

No comments