manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 89

 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

89 

Chapter 8 

Backup, Restore and Upgrade 

1  The System and Data Cards and USB memory stick 

The Hydro-Control incorporates a System Card and a Data Card.  These cards are accessed via 

the top access plate.  The identification, removal and replacement of these cards is described in 

Chapter 2. 

1.1 

The System Card (Hydronix Replacement Part Number 0176)  

The System Card holds the main operating files of the Hydro-Control.  This is specific to the 

type of unit and should not be changed between units. (Not applicable to HC06 v2) 

1.2 

The Data Card (Hydronix Replacement Part Number 0177)  

The Data Card holds the mix log database and system settings.  With the power supply off, this 

can be removed and replaced if necessary. (Not applicable to HC06 v2) 

1.3 

USB Memory Stick 

 

Figure 52: The Hydro-Control VI side view showing the USB ports 

There are three USB ports sited on the left hand side when looking at the front of the unit.  A 

Memory Stick may be used for backing up and restoring recipes, system parameters and mix 

log files. 

If the  Hydro-Control USB ports are difficult to access then a USB extension with a panel 

mounted socket is available from Hydronix – Part Number 0175. 

The Memory Stick may be inserted and removed with the power supply on.  Do not remove the 

Memory Stick when a backup or restore is in progress. 

The USB ports 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands