manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 85

 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

85 

Chapter 7  

Remote Support 

Remote support allows a remote connection to the HC06 unit via an Ethernet connection. The remote 

party, using a standard PC can view, control and change the configuration of the HC06 during its 

operation, from any location with an internet connection. This facility allows distributors, installers and 

site managers to offer assistance to operators who may be having difficulties configuring or operating 

the HC06. 

To avoid difficult Ethernet setup configurations, Remote Support uses a connection server at a third 

party location. The HC06 requires only a basic Ethernet connection to the internet, such as one that 

would normally allow internet browsing. A connection is established with the third party server and the 

remote party wishing to control the HC06 also connects to the same server using a simple  client 

software package. Control of the HC06 is then established. 

Remote support can be configured to use either the Hydro-Control VI support server provided by 

Hydronix or another server which an installer or local distributor may choose to set up for themselves. 

To access the remote support configuration press 

  followed by 

.  The 

communications page will now be displayed.  Press 

, the Ethernet Comms  page is now 

displayed. 

 

 

Figure 49 - Ethernet Coms Page 

1  Remote support using Hydronix Hydro-Control VI support 

server 

The remote support server by default points at the Hydronix remote support server.  This is 

hc06support.hydronix.com.  The installer should change the remote support telephone number to 

the installers customer support telephone number. 

The installers customer support team should install the client software UltraVNC viewer,  on 

customer support PCs.  This is available from  http://www.uvnc.com/download/index.html or is 

available from Hydronix on request. 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands