manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 40

Commissioning 

Chapter 4 

40 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

General Settings 

Parameter 

Units 

Default 

Range 

Language 

None 

English 

Multiple Languages 

Max Mix Logs 

None 

100 

1-1000 

Archiving 

None 

True 

True/False 

 

The 

Language

 parameter sets the Hydro-Control to display different languages. 

The 

Max Mix Log

 parameter limits the maximum number of mix logs saved to the database. 

The

 Archiving 

parameter, when selected, will enable the HC06 to save all mix log data that 

exceeds the Max Mix Logs limit to an archive file. Once the Max Mix log limit has been reached 

any Mix Logs that are removed from the main database are copied to the archive file. If a USB 

memory stick is inserted into the HC06, and a Backup is requested, the archive files will be 

copied to the USB stick. This will enable the user to keep a record of older mix logs.   

  

Alarms Setup 

The Alarms Setup section on the System Parameters page allows each of the alarms in the 

system to be disabled.  The alarms are described in the Operators Guide in the chapter ‘Alarm 

Configuration’. 

At the end of a batch, if the sensor value has not fallen below the 

Mixer Blades Worn Value

 

by the end of the 

Mixer Blades Worn Time

, then the 

Mixer Blades Worn Alarm

 is activated. 

5.3 

The System Parameters – Page 3 

By clicking the Next button 

 the internal temperature and voltage monitoring page is 

displayed.  This is for system information only. 

The screen shown in Figure  26  displays the current parameters available from the Hydro-

Control and is used for diagnostic monitoring purposes. 

 

Figure 26: The voltage and temperature monitor screen 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands