Husqvarna F2303U7 Owner'S Manual Download Page 50

Page: 50 / 171

11 TUNING THE CHASSIS

H03672-10

–

Turn adjusting screw

clockwise with a screwdriver as far

as the last perceptible click.

Info

Do not loosen fitting

–

Turn counterclockwise by the number of clicks correspond-
ing to the shock absorber type.
Guideline

Lowspeed compression damping

Comfort

17 clicks

Standard

15 clicks

Sport

13 clicks

Info

Turn clockwise to increase damping; turn counter-
clockwise to reduce damping.

11.4

Adjusting the high-speed compression damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will move around if the shock absorber is detached incor-

rectly.
The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be
glad to help.)

Info

The effect of the high-speed compression adjuster can be seen in fast compression of the shock
absorber.

H03673-10

–

Using an open end wrench, turn adjusting screw

clock-

wise all the way.

Info

Do not loosen fitting

–

Turn counterclockwise by the number of turns corresponding
to the shock absorber type.
Guideline

Highspeed compression damping

Comfort

2.5 turns

Standard

2 turns

Sport

1.5 turns

Info

Turn clockwise to increase damping; turn counter-
clockwise to reduce damping.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands