Husqvarna F2303U7 Owner'S Manual Download

Page: 97 / 171

BRAKE SYSTEM 13

H03724-10

Main work

–

Stand the vehicle upright.

–

Remove the cable ties on the frame protector.

–

Remove screw cap

with membrane

and the shim.

–

Add brake fluid up to the marking

Brake fluid DOT 4 / DOT 5.1 (

p. 157)

–

Mount and tighten screw cap with the membrane and the
shim.

Info

Clean up overflowed or spilled brake fluid immediately
with water.

–

Mount new cable ties on the frame protector.

13.11

Checking the brake linings of the rear brake

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy-
cles workshop will be glad to help.)

H03725-10

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the rear brake linings.

(

p. 95)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the rear brake linings.

(

p. 95)

13.12

Changing the rear brake linings

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna
Motorcycles workshop will be glad to help.)

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands