Husqvarna F2303U7 Owner'S Manual Download Page 127

Page: 127 / 171

COOLING SYSTEM 16

125

S04264-10

–

Unplug connector

–

Remove thermostat

with O-ring and wait until the coolant

escapes without bubbles.

–

Mount thermostat

with the O-ring and tighten.

Guideline

Screw, cylinder head
temperature sensor

M10x1.25

12 Nm (8.9 lbf ft)

–

Plug in connector

–

Mount protection cap

S04265-10

–

Mount radiator cap

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and
death.

–

Always make sure there is sufficient ventilation
when running the engine.

–

Use effective exhaust extraction when starting or
running the engine in an enclosed space.

–

Allow the engine to warm up and cool down again.

–

Check the cooling system for leaks.

–

Check the coolant level. (

p. 121)

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands