Husqvarna F2303U7 Owner'S Manual Download Page 102

Page: 102 / 171

14 WHEELS, TIRES

100

H01890-10

(All TE special models)

–

Remove spacer

and brake disc guard

14.2

Installing the front wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H00935-10

(All TE standard models)

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change front wheel bearing.

–

Clean and grease shaft seal rings

and contact sur-

faces

of the spacers.

Long-life grease (

p. 159)

–

Insert the spacers.

–

Clean and grease the wheel spindle.

Long-life grease (

p. 159)

S01631-10

(All TE special models)

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change front wheel bearing.

–

Clean and grease shaft seal rings

and contact sur-

faces

of the spacers.

Long-life grease (

p. 159)

–

Insert the spacers.

–

Clean and grease the wheel spindle.

Long-life grease (

p. 159)

F02590-10

–

Align the brake disc guard so that distance

and

are equal in size.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands