Husqvarna F2303U7 Owner'S Manual Download

Page: 70 / 171

12 SERVICE WORK ON THE CHASSIS

F02309-10

–

Attach frame protector in area

and position.

–

Mount and tighten screws

with the washers.

Guideline

Screw, frame pro-
tector

3 Nm (2.2 lbf ft)

–

Mount the new cable ties.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 56)

12.18

Removing the seat

Preparatory work

–

Remove the air filter box cover. (

p. 69)

F02310-10

Main work

–

Remove screw

H02218-10

–

Raise the rear of the seat, pull the seat back, and lift it off.

12.19

Mounting the seat

H02218-11

Main work

–

Mount the front of the seat on the collar bushing of the fuel
tank and the rear in the bracket.

–

Push the seat forward.

–

Make sure the seat is correctly latched in place.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands