Husqvarna F2303U7 Owner'S Manual Download

Page: 128 / 171

17 TUNING THE ENGINE

126

17.1

Checking the play in the throttle cable

400192-11

–

Check the throttle grip for smooth operation.

–

Turn handlebar as far as possible to the right. Turn the
throttle grip back and forth slightly and determine the play in
throttle cable

Play in throttle cable

3 … 5 mm (0.12 … 0.2 in)

» If the throttle cable play does not meet the specified

value:

–

Adjust the play in the throttle cable.

(

p. 126)

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and
death.

–

Always make sure there is sufficient ventilation
when running the engine.

–

Use effective exhaust extraction when starting or
running the engine in an enclosed space.

–

Start the engine and let it run at idle speed. Move the handle-
bar to and fro over the entire steering range.

The idle speed must not change.

» If the idle speed changes:

–

Adjust the play in the throttle cable.

(

p. 126)

17.2

Adjusting the play in the throttle cable

Info

If the correct routing of the throttle cables has already been secured, the fuel tank does not need to be
removed.

Preparatory work

–

Remove the air filter box cover. (

p. 69)

–

Remove the seat. (

p. 68)

–

Remove the right side cover. (

p. 73)

–

Remove the fuel tank.

(

p. 74)

–

Check the throttle cable routing. (

p. 82)

F02324-10

Main work

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

–

Loosen nut

–

Turn adjusting screw

in as far as possible.

–

Loosen nut

–

Turn adjusting screw

in as far as possible.

–

Turn adjusting screw

so that there is play in the throttle

cable at the throttle grip.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands