Husqvarna F2303U7 Owner'S Manual Download

Page: 83 / 171

SERVICE WORK ON THE CHASSIS 12

H03710-10

–

Check the chain sliding piece for wear.
» If the lower edge of the chain pins is in line with or below

the chain sliding piece:

–

Change the chain sliding piece.

–

Check that the chain sliding piece is firmly seated.
» If the chain sliding piece is loose:

–

Tighten screw on the chain sliding piece.
Guideline

Screw, chain slid-
ing piece

15 Nm
(11.1 lbf ft)

401760-01

–

Check the chain guide for wear.

Info

Wear can be seen on the front of the chain guide.

» If the light part of the chain guide is worn:

–

Change the chain guide.

H03711-01

–

Check that the chain guide is firmly seated.
» If the chain guide is loose:

–

Tighten the screws on the chain guide.
Guideline

Remaining
screws, chassis

10 Nm (7.4 lbf ft)

Remaining nuts,
chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 56)

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands