Husqvarna F2303U7 Owner'S Manual Download

Page: 99 / 171

BRAKE SYSTEM 13

H03726-10

–

Position the vehicle upright.

–

Remove the cable tie on the frame protector.

–

Remove screw cap

with membrane

and the shim.

H03727-10

–

Manually press the brake caliper toward the brake disc to
push back the brake piston. Ensure that brake fluid does not
flow out of the brake fluid reservoir; extract some if neces-
sary.

Info

Make sure that you do not press the brake caliper
against the spokes when pushing back the brake pis-
ton.

–

Remove cotter pin

–

Push spring plate

downwards and remove pin

–

Remove the brake linings.

–

Clean the brake caliper and the brake caliper bracket.

H03728-10

–

Check that spring plate

in the brake caliper and sliding

plate

in the brake caliper bracket are seated correctly.

H03729-10

–

Insert the new brake linings.

–

Mount pin

Spring plate

engages in the groove on the pin.

Info

Always change the brake linings in pairs.
Make sure that decoupling plate

is mounted on

the piston side brake lining.

–

Mount cotter pins

–

Operate the foot brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands