Husqvarna F2303U7 Owner'S Manual Download Page 104

Page: 104 / 171

14 WHEELS, TIRES

102

Info

Do not operate the foot brake lever when the rear
wheel is removed.

H03002-10

–

Remove spacers

14.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H03001-10

Main work

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Clean and grease shaft seal rings

and contact

surfaces

of the spacers.

Long-life grease (

p. 159)

–

Insert the spacers.

H03735-10

–

Clean and grease the wheel spindle.

Long-life grease (

p. 159)

–

Position rear wheel and insert wheel spindle

The brake linings are correctly positioned.

–

Mount the chain.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands