Husqvarna F2303U7 Owner'S Manual Download Page 147

Page: 147 / 171

TROUBLESHOOTING 21

145

Faults

Possible cause

Action

Engine does not speed up

Faulty ignition

–

Ignition coil - check the primary wind-
ing.

–

Check the spark plug connector.

–

Check the stator winding of the alter-
nator.

Ambient pressure is incorrectly
stored

–

Program ambient air pressure.
(

p. 129)

Engine has too little power

Air filter very dirty

–

Clean the air filter and air filter box.
(

p. 70)

Fuel filter is very dirty

–

Change the fuel filter.

Fuel screen is very dirty

–

Change the fuel screen.

(

p. 131)

Malfunction in the electronic
fuel injection

–

Read out the fault memory using the
Husqvarna Motorcycles diagnostics
tool.

Fuel supply interrupted

–

Check the fuel tank breather.

Exhaust system leaks,
deformed or too little glass
fiber yarn filling in the main
silencer

–

Check exhaust system for damage.

–

Change the glass fiber yarn filling of
the main silencer.

(

p. 72)

Faulty ignition

–

Ignition coil - check the primary wind-
ing.

–

Check the spark plug connector.

–

Check the stator winding of the alter-
nator.

Diaphragm or reed valve hous-
ing damaged

–

Check the diaphragm and reed valve
housing.

Ambient pressure is incorrectly
stored

–

Program ambient air pressure.
(

p. 129)

The engine dies during the trip

Lack of fuel

–

Refuel. (

p. 42)

The engine takes in false air

–

Check that the intake flange is firmly
seated.

The connector or ignition coil
is loose or oxydized

–

Clean the connector and treat with
contact spray.

Ambient pressure is incorrectly
stored

–

Program ambient air pressure.
(

p. 129)

Engine overheats

Too little coolant in cooling
system

–

Check the cooling system for leakage.

–

Check the coolant level. (

p. 121)

Too little air stream

–

Switch off engine when stationary.

Radiator fins very dirty

–

Clean the radiator fins.

Foam formation in cooling sys-
tem

–

Drain the coolant.

(

p. 121)

–

Refill with coolant.

(

p. 122)

Damaged cylinder head or
cylinder head gasket

–

Check the cylinder head and cylinder
head gasket.

Bent radiator hose

–

Change the radiator hose.

Thermostat defective

–

Check the thermostat.
Guideline
Opening temperature: 70 °C (158 °F)

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands