Husqvarna F2303U7 Owner'S Manual Download

Page: 133 / 171

SERVICE WORK ON THE ENGINE 18

131

18.1

Changing the fuel screen

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

F02317-10

–

Clean quick release coupling

thoroughly with

compressed air.

Info

Under no circumstances should dirt enter into the fuel
line. Dirt in the fuel line clogs the injection valve!

–

Disconnect the quick release coupling.

Info

Remaining fuel may flow out of the fuel hose.

–

Pull fuel screen

out of the connecting piece.

–

Insert the new fuel screen all the way into the connecting
piece.

–

Spray silicone spray onto a lint-free cleaning cloth and lightly
lubricate the O-ring of the quick-release coupling.

Silicone spray (

p. 159)

–

Join the quick release coupling.

Summary of Contents for F2303U7












































































































































































Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands

Husqvarna F2303U7, Owner'S Manual

Search results

Summary of Contents for F2303U7

Reviews:

Related manuals for F2303U7

Brands by name

Popular brands