Hughes 9201 User Manual Download Page 19

Page: 19 / 147

BGAN 9201 User Manual

ONNECTING BY

USB

To connect the BGAN terminal to the computer using the USB port:

Connect the supplied USB cable to your computer‟s USB port, and insert the other end of the
connector into the BGAN terminal‟s USB port.

At the terminal, slide the cable through the rubber door slot in order to secure and protect
the connection.



Note

When plugging in the USB cable for the first time, you will see Windows installing a
new driver for the device.

USB drivers for the terminal are available from: www.inmarsat.com/support or
www.bgan.hughes.com.

When you plug in the USB cable into your computer for the first time, your computer will
detect that new USB Hardware has been connected. You should then follow the computer‟s
instruction to install the

Hughes USB LAN LINK

driver software (for computers using the

Windows operating system, the installation is carried out using a

Found New Hardware

Wizard

). Your computer will then use this driver to connect to the terminal.

Summary of Contents for 9201




















































































































































Search results

Summary of Contents for 9201

Reviews:

Related manuals for 9201

Brands by name

Popular brands

Hughes 9201, User Manual

Search results

Summary of Contents for 9201

Reviews:

Related manuals for 9201

Brands by name

Popular brands