Huawei RRU3269 Installation Manual Download Page 20

Page: 20 / 135

RRU3269
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Figure 3-5

Requirements for the vertical deviation angle of an RRU

(1) RRU

(2) Installation support (pole, U-steel, angle steel, or wall)



When the operator faces the RRU whose handle and cabling cavity are on the right-hand side, the
side facing the operator is the front of the RRU, and the other side is the back of the RRU.



Standard installation: RRU mounting kits are installed on the back of an RRU.



Reverse installation: RRU mounting kits are installed on the front of an RRU.



Side-mounted installation: RRU mounting kits are installed on the side face (not the side face of the
maintenance cavity) of an RRU.



Stacked installation: Two or more RRUs are installed next to each other at the same level by
stacking multiple RRU mounting kits.

Installing an RRU on a Pole

Figure 3-6 shows the diameter of a pole for installing an RRU.

Figure 3-6

Diameter of a pole

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands