Huawei RRU3269 Installation Manual Download Page 4

Page: 4 / 135

RRU3269
Installation Guide

About This Document

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

iii

This chapter describes how to unpack and check the delivered equipment to ensure that all the
materials are included and intact.

5 Installation Process

The installation process involves installing an RRU and RRU cables, checking the RRU
hardware installation, and powering on an RRU.

6 (Optional) Installing the Plastic Shells of the RRU

This section describes the procedure for installing the plastic shells of the RRU.

7 Hoisting an RRU and Related Cables onto a Tower

This section describes the procedure for hoisting an RRU and related cables onto a tower and
the precautions that must be taken.

8 Installing the RRU

This chapter describes the procedure for installing the RRU. The procedure for installing the
RRU varies depending on installation options.

9 Installing RRU Cables

This chapter describes the procedure for installing RRU cables.

10 Checking the RRU Hardware Installation

After an RRU is installed, check the hardware installation.

11 Powering On an RRU

After all the devices are installed, check the power-on status of an RRU.

12 Appendix

Conventions

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands