Huawei RRU3269 Installation Manual Download Page 30 | Manualshive

Page: 30 / 135

background image

RRU3269
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

22

If an RRU is installed on the bitumen ground, the RRU must be at least 500 mm (700 mm or
more is recommended) away from the bitumen ground. The following describes the space
requirements for installing a single RRU on the non-bitumen ground.



The recommended clearances ensure normal running and provide appropriate space for operation
and maintenance (O&M). If the installation space is sufficient, leave the recommended clearances
after installing the equipment.



The minimum clearance ensures normal running and heat dissipation, but O&M activities such as
checking indicator status and opening the cabling cavity cannot be properly conducted. If the
installation space is restricted, leave the minimum clearance after installing the equipment.

Clearance for a Single RRU in Side-Mounted Mode

Figure 3-21 shows the clearance for a single RRU in side-mounted mode.

«
...
28
29
30
31
32
...
»

Summary of Contents for RRU3269








































































































































Reviews:

No comments

Related manuals for RRU3269

Brand: Handicare Pages: 56

Brand: NEC Pages: 149

Brand: NEC Pages: 13

Brand: UNITED Pages: 8

Brand: Oceanic Pages: 11

Brand: Omega Pages: 56

Brand: Omega Pages: 2

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: Rain Bird Pages: 20

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

Brand: Watts Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands