Huawei RRU3269 Installation Manual Download Page 121

Page: 121 / 135

RRU3269
Installation Guide

9 Installing RRU Cables

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

113

Figure 9-25

Opening clips

Step 4

Remove the waterproof block.

Remove only the waterproof blocks for the cables to be installed.

----End

9.10 Installing a CPRI Optical Fiber

This section describes the procedure for installing a CPRI optical fiber.

Prerequisites

Before the installation, single-mode optical modules can be distinguished from multimode
optical modules in either of the following ways:



SM and MM labels on an optical module: SM indicates a single-mode optical module,
and MM indicates a multimode optical module.



Color of the puller on an optical module: Blue indicates a single-mode optical module,
and black or gray indicates a multimode optical module.

The optical modules to be installed must match CPRI rates.

Summary of Contents for RRU3269








































































































































Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands

Huawei RRU3269, Installation Manual

Search results

Summary of Contents for RRU3269

Reviews:

Related manuals for RRU3269

Brands by name

Popular brands